Home > Printer Error > 51.2y Printer Error 4600

51.2y Printer Error 4600

Contents

Release the (Select) button when the Ready, Data, and Attention light are on steady. alternates with TO CONTINUE PRESS 68.0 PERMANENT STORAGE FULL FOR HELP PRESS ? alternates with LOAD TRAY XX: [TYPE] [SIZE] Description Paper is loaded that is longer or shorter in the feed direction than the size configured for the tray. Check for any non-HP memory DIMMs. navigate here

Continue holding the (Select) button until the Ready, Data, and Attention lights flash once, and then stay on steady. Press (Down Arrow) button once. The control panel will display SELECT LANGUAGE . Description Non-HP black print cartridge installed.

Hp 4600 Laser Scanner Assembly

Press the green (Select) button to continue. X PRINTER ERROR FOR HELP PRESS ? Check for additional paper in the paper path. 13.12.00 JAM IN DUPLEX PATH X For help press ?

When the memory starts counting, press and hold the green (Select) button. clean the inside of the printer or check it. Printing cannot continue. 54.2X PRINTER ERROR There is a problem with a toner level sensor. 51.2y Printer Error 5500 For use in the HP Color LaserJet 4600 series, not for use in the 4610 or 4650 series.

Your answer needs to include more details to help people. 51.2k Printer Error 5500 NOTE: This is considered a major repair. Action Ensure print cartridge is a Genuine HP cartridge. https://www.printertechs.com/shop/laser-scanner-assembly-for-hp-color-laserjet-4600-series-rg5-6390 Press (Select) to resume printing.

Watch the control panel. 51.2k Printer Error Hp 4600 Turn off the printer. To ensure the tests are valid, turn the printer off and on between steps to determine if the error message has been cleared. or it's affiliates.

51.2k Printer Error 5500

Perform a cold reset on the printer. When the display begins showing the memory count, press and hold (Down Arrow) until all three lights on the control panel are lit. Hp 4600 Laser Scanner Assembly Description There are multiple paper jams in the paper path or duplex path. Laser Scanner Assembly For Hp Color Laserjet 4600 Series Alejandro Rodriguez 480 (na) panonood 1:15 The Best of Cats vs.

The printer will initialize NVRAM and then continue its power-on sequence. http://postmapper.com/printer-error/59-5a00-hp-4600-error.html Pull open the front cover. Lift the top cover. Action Turn the printer off, and turn it on again. 51.2c Printer Error

Watch the control panel. alternates with TO CONTINUE PRESS Description One or more settings saved in the onboard NVRAM or removable disk (flash or hard) have been reset to the factory defaults. Turning the printer off and then on can clear some of these messages. his comment is here Expert 111 Answers Re: hp colour laserjet 4600dn, 51.2Y error...how to solve...

Reinstall the fuser. Hp 4600 Laser Scanner Replacement Click "Add" to insert your video. Lift the fuser by grasping the fuser housing above the green arrow on the left and right.

Press (Select).

One of the covers is not completely closed. If the message persists, adding additional memory to the printer may allow printing of more complex pages. 22 EIO X BUFFER OVERFLOW alternates with TO CONTINUE PRESS Too much data was Continue holding the (Select) button until the Ready, Data, and Attention lights flash once, and then stay on steady. Rg5-6380 The control panel will display COLD RESET .

Action Turn the printer off, and turn it on again. If the 80 SERVICE error continues, remove and reinstall the Jetdirect card, installing the card in the other EIO slot provided in the printer. Some error messages are auto-continuable; if AUTO CONTINUE=ON the printer will continue normal operation after displaying an auto-continuable error message for ten seconds. http://postmapper.com/printer-error/4600-51-2-m-error.html This may be unsupported memory.

Add × Loading... From Woody Friesen: Did the printer have a rough ride? Continue holding the green (Select) button until the Ready, Data, and Attention lights flash once, and then stay on steady. Scholar: An expert who has written 20 answers of more than 400 characters.

Press (Down Arrow) button once. There may be a problem with the printer's fuser, or inadequate external or internal power supply/line voltage. 50.5 An inconsistent fuser error has occurred, possibly due to an inadequate external or Watch the control panel. If CLEARABLE WARNING is set to JOB in the printer’s configuration menu, these messages are cleared by the next print job.

Posted on Dec 24, 2008 Helpful 7 Not Helpful Comment Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Add Your Answer Tips for a If the error persists, execute NVRAM initialization. The printer will perform a cold reset and then continue its power-on sequence.

© Copyright 2017 postmapper.com. All rights reserved.