Home > Printer Error > 4600n Error

4600n Error

Contents

Turn off the printer. When the memory starts counting, press and hold the green (Select) button. Action Press (Select) to clear the message and continue printing. Clean the color registration detection sensor above the black print cartridge if the error does not clear.

Press (Select). Cold reset the printer. If using DDR SDRAM for the HP Color LaserJet 4650, make sure it meets specifications and is correctly seated. The printer will perform a cold reset and then continue its power-on sequence.

Hp 4600 Laser Scanner Assembly

Check the paper pickup assembly for jammed media. Inspect the fuser for media or damage, and then reseat the fuser. Press (Down Arrow) button once. Action Press (Select) to resume printing.

Turn on the printer. Press (Select). Release the (Select) button when the Ready, Data, and Attention light are on steady. 51.2k Printer Error 5500 Press (Select) to select PRINT QUALITY .

Check that all print cartridge shutters are opening and closing in unison while opening and closing the ETB. 51.2c Printer Error Press (Select). Turn on the printer. Laser Printer Services carries all necessary LaserJet 4600 printer service parts to provide complete printer repair at one visit.

Perform a cold reset on the printer. 51.2y Printer Error 5500 If using DDR SDRAM for the HP Color LaserJet 4650, make sure it meets specifications and is correctly seated. Pull paper by both corners to remove it. The printer will initialize NVRAM and then continue its power-on sequence.

51.2c Printer Error

Watch the control panel. browse this site Action Ensure print cartridge is a Genuine HP cartridge. Hp 4600 Laser Scanner Assembly The control panel will display COLD RESET . 51.2y Error 4600 Watch the control panel.

I did so, but it did not help :- PCL 5 gave the same result- PS prints a part of the document, before printing out a second page with the following If the error returns, remove the yellow cartridge and turn off the printer. Turn the printer off, and turn it on again. button on the control panel for detailed information about clearing the jam. Laser Scanner Assembly For Hp Color Laserjet 4600 Series

If the 79 error disappears after removing all the accessories, start adding the accessories back one at a time to isolate which one is causing the issue. The control panel will display COLD RESET Hewlett Packard Color LaserJet 4600/ HP CLJ 4600 Printer Specification! The control panel will display COLD RESET Press (Select). HP LaserJet 4600 Fuser Unit, Color LaserJet 4600 Maintenance Kit, 4650 paper cassette tray, HP Color LaserJet 4600 Transfer Belt Kit, HP color laser 4600 paper pickup assembly, HP LJ 4600

Press (Select). Rg5-6380 Open the covers and the Electrostatic Transport Belt (ETB). Locate the green square tab on the right of the fuser flap and lift it to inspect the fuser roller for media or damage.

Please try again later.

Action Turn the printer off, and turn it on again. top 51.XY PRINTER ERROR FOR HELP PRESS ? Turn the printer off, and turn it on again. 53.X0.ZZ PRINTER ERROR TO CONTINUE TURN OFF THEN ON An error has occurred in the onboard RAM. Hp Color Laserjet 4600 Error Codes Turn on the printer again.

When the memory starts counting, press and hold the green (Select) button. Watch the control panel. This can be done by lowering the resolution of graphics and/or printing at a lower resolution. If the error returns, remove all print cartridges and turn off the printer.

Register Help Remember Me? Press (Select). Press (Down Arrow) button once. Press (Down Arrow) button once.

alternates with TO CONTINUE PRESS 68.X PERMANENT STORAGE ERROR SETTING CHANGE FOR HELP PRESS ? Thank you! Register ยท Log In HP Support Forum Home > Printers > LaserJet > PCL XL Error, Subsystem: Image - HP color Laserjet 4600n HP Support Forums Join Remove all accessories that have been installed on the printer (for example, EIO Cards, RAM/ROM DIMMS). Description The printer cannot read or write to the print cartridge memory tag.

Release the check button when the Ready, Data, and Attention light are on steady. The four laser / toner motors spin OK and the disengagement bar seems to be moving it's full range (up and down). Release the check button when the Ready, Data, and Attention light are on steady. Power on the printer.

These messages are not affected by the AUTO CONTINUE setting. Turn the printer off, and turn it on again. Press (Select). If this message persists, contact an HP-authorized service or support provider.

I have had this problem before, but it always eventually responded to power cycling. Turn the printer off, and turn it on again. If this message persists, contact Laser Printer Services at (800)815-2737 58.4 PRINTER ERROR FOR HELP PRESS alternates with TO CONTINUE TURN OFF THEN ON A power supply error while reading a If this message persists, contact an HP-authorized service or support provider top 54.11 PRINTER ERROR Description There is a problem with the black density sensor.

The control panel will display COLD RESET .

© Copyright 2017 postmapper.com. All rights reserved.