Ok back the printer. by unknown on Jun 23, 2004 at 4:43am Add comment Please sign in to comment 0 I have checked out the power supply whichs seems ok but i have noticed the X description: 0 = Motor error 1 = Motor startup error 2 = Motor rotation error 1. If the image is dark, then you have a transfer roller issue. http://postmapper.com/fuser-error/502-fuser-error-hp.html
All gears are rotating free. You painted a bullseye on the problem right down to the pin. It could have NO paper inside due to paper pickup failures. Thanks again, and keep making these videos.
I have replaced the toner and fuser with known good ones and I am still having the same problem. I'm going to subscribe. Leave a Reply Cancel reply Enter your comment here... Power is going in on the DC controller but only 0.6V DC is going to the main motor.
by unknown on Sep 8, 2003 at 7:03pm Add comment Please sign in to comment 0 There is no problem with the whole fuser unit assembly.I found the problem -- Powersupply I'll take pictures and post them if I can for others. - Andy Z 0 Thank you to all who have posted on this.I had, notice the had, 2 8150's that Replace. 50.1 Fuser Error On Hp Laserjet 8100 And 8150 Any help would greatly be appreciated thanks Toxicmonkeylove (TML) MichaelTech01-15-2008, 10:22 AM1st} One of the lamps is bad.
Add to Want to watch this again later? 50.1 Fuser Error Hp 3600 So I installed another toner (new) to see if it was a badtoner cartridge. Bookmark the permalink. browse this site Sofar it looks good.
thank you very much video It's very helpful Posted by Unknown on 19th Jul 2012 thank you very much very helpful Showing reviews 1-4 of 12 | Next Customers Who Viewed 50.1 Fuser Error Hp Cp4005 Thanks. by msr976 on Nov 15, 2006 at 6:24am Add comment Please sign in to comment 0 You can use a paper clip to keep the shutter open. I have never had a 5si, 8000 or surprisingly a 8100 with a LVPS induced 50.1.
I too can not see the printer printing blank pages with the 50 error. http://www.fixyourownprinter.com/posts/41389 I don't have another LVPS to swap out, but do you have any more suggestions?Thanks. - Anonymous Yeah, they are. 50.1 Fuser Error Hp 4700 by unknown on Jul 24, 2006 at 9:51am Add comment Please sign in to comment 0 I have HP LaserJet 8150 Printer don't star. 50.1 Fuser Error 9050 by unknown on Sep 5, 2003 at 6:38pm Add comment Please sign in to comment 0 There is nothing wrong with the fuser unit.The problem is from the powersupply.-- Dc woltage
The solder joint on the middle pin of Q600 wasn't very pretty either so I touched it up too. by msr976 on Nov 15, 2006 at 6:23am Add comment Please sign in to comment 0 You can use a paper clip to keep the shutter open. Interestingly enough when the rebuilt was put in and the time came to initialize the fuser there was a noticeable POP. weblink Palencia 68,980 views 21:45 Top Ten Color Laser Printers 2015 | Best Color Laser Review - Duration: 5:33.
Using all capital letters is shouting. 50.1 Fuser Error Hp 8150dn Wrote HP a letter asking about their lack of quality control...Still waiting for an answer, thanks for your advice. Is it possible that one or more of those are out of tweak, and if so is there any way to (safely) measure the voltage coming out (while it's not connected
Cold Reset will appear on the menu and then initializing will appear. Keep in mind there is also the cable which runs from the low voltage ps to the fuser loom. by unknown on Apr 24, 2006 at 3:49pm Add comment Please sign in to comment 1 You can use a paper clip to keep the shutter open. Fuser Error 50.1 Hp Laserjet 4700dn Go to this link:http://partsurfer.hp.com/cgi-bin/spi/mainYou could try partsnow.com or depot-america.com or even email Moe at this site, but the part is pricey.
by unknown on Feb 16, 2006 at 1:07pm Add comment Please sign in to comment 0 The Q600 triac, center pin, was missing solder alltogether and had a burn spot. I turned it off and uplugged it. Glad I came across this forum. http://postmapper.com/fuser-error/50-0-fuser-error.html There was a hair line break all the way around the pin.
You may test it. I figured there's no way this would be covered on a 6+ year old printer who's warranty is long expired. kit. If we can't fix them by "waving our magic wands," they junk 'em and just buy new printers.
Thanks again! - AMT 0 Oheady,Unfortunate, but not unusual.ST by Stephen on Nov 27, 2005 at 5:36pm Add comment Please sign in to comment 0 I have 2 that are exibiting hard to miss it once you take off the back cover.http://h20141.www2.hp.comit's the large rectangle part in this diagram .. it was easy. the power supply is good I chek volt.
So it must have something to do with one of those sensors a pervious poster was talking about. If other items are on the same circut when they draw power, it could reduce the power available to the 5SI and cause a 50.1 error. I know when I replaced mine I received the metal casing and everything attached.http://catanich.com/detail.asp?pn=RG5-4357-000Call the 800 #.This is a link to a website for Printer Parts Solutions. Remove the duplexer if yours is equipped and see if it goes away after power down and power on.
off the top of my head I think you have to remove the fan on located just above the plug to access one of the screws but other than that it's Sign in to make your opinion count. My experience has been the same. 99\% of the time it is the lvps. You can solder it but don't mess with the chip type components - it's the legs of the triacs, generally the center of the three n each triac - that has
Great information! Since the fuser is hot to the touch, then you can basically eliminate the LVPS and the fuser. Can you give me some step-by-step advice as for what exactly I'm looking for? This will get things going again until I get a part.