Home > Fuser Error > 502 Fuser Error

502 Fuser Error

Contents

If you do not wait 20 mins then the 50 error will appear again even if the problem is fix. by redd44 on Aug 18, 2015 at 4:06pm Add comment Please sign in to comment 0 if you are using a good fuser the next part to try would be low If one track of the heater has gone it will be markedly higher. I'll post results in a couple days when the new fuser unit (#3) arrives. http://postmapper.com/fuser-error/502-fuser-error-hp.html

When you stated you got a 220v fuser it made it sound like you knew what you ordered and knew thats what you needed. Flip it to the gear side (the left side) and press inwards on the fuser tab to make sure it is fully clicked in place, as shown below. A person would have to go out of his way to get a 220V fuser in the U.S. Turn the product power on.

50.2 Fuser Error P4015

Consider having a replacement toner cartridge available. The problem turned out to be power related. Since it was only getting half the voltage it was supposed to be getting, it wasn't getting hot enough to fuse the toner, but it didn't trip the error either. What you did might have been a Maintenance reset, but that just clears the counter.

To see if you have the same issue just print from the manual feeder or set the switch in the paper tray to custom and the black strip will disappear. Furthermore the fuser heater is deeply buried in the mechanism so an attempt to get at it really means a complete " refurb" of the fuser - which is time consuming Recommended action Close the door. 50.1 Fuser Error The fuser is cold.

by unknown on May 29, 2009 at 7:29am Add comment Please sign in to comment 0 There is no fuser reset. If the message persists, contact HP support. If you believe you purchased an HP supply, go to www.hp.com/go/anticounterfeit . http://printerrepairsupport.com/50-2-fuser-error-hp-4240-4250-4350/ The service manual indicated some ohms testing to be done on the problem fuser and all results came back showing all the correct readings.

by unknown on Mar 5, 2009 at 8:04am Add comment Please sign in to comment 0 You're correct. 50.2 Fuser Error 4250 Posted on Oct 19, 2010 Helpful 0 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Add Your Answer Tips for a great I'm following dmzcompute's advice, I tried the "High1" setting, but the fuser isn't heating up at all.I can see some obvious damage to the first fuser tried (the one that worked Recommended action Press the OK button to continue printing.

50.2 Fuser Error Laserjet Pro 400

Turn off the product, wait at least 25 minutes, and then turn on the product. Delete all print jobs from all computers connected to the printer. 50.2 Fuser Error P4015 That was after registration, dc controller and ps replacement. 50.2 Fuser Error Hp 4700 Ask Loading...Oops :Please try again.

However it is also possible for the fuser not to reach temperature because the supply voltage is inadequate in some way. http://postmapper.com/fuser-error/922-fuser-error.html This made me wonder if it would even have enough time to heat up enough to know it had a low temp problem. If you are using a surge protector, remove it. I didn't feel the advice was very sound. 50.2 Fuser Error P3015

I got it figured out on my own though, thanks for the information I got off of here. by moe on Jun 20, 2008 at 11:18am Add comment Please sign in to comment 0 can a hp4250dtn be used in the U.S. The fuser has two thermistors, one called the TH1 main thermistor offset about 25mm from the centre-line and another called the TH2 sub-thermistor almost at the paper edge. http://postmapper.com/fuser-error/50-0-fuser-error.html Used black cartridge is installed Press [OK] to continue Description You are using a toner cartridge that reached the default low threshold while it was installed in another product.

Break the job into smaller jobs that contain fewer pages. 50.2 Fuser Error Hp 5100 marketpoint.com Almost nothing beyond cut and paste from the service manual. Operation of the circuit goes along the following lines.

In the US power is supplied at a nominal 120 volts or so.

If you have NOT recently replaced the fuser or heavily jostled the printer around, then the 50.2 Fuser error indicates you may have an actual fuser failure and the fuser needs Besides this there has been a rash of fusers sent out from either HP or sub vendors labeled RM1-0013 for the LJ 4200 BUT the fusers are actually for the LJ If you are using a surge protector, remove it. 50.2 Fuser Error Hp Laserjet 4050 Remove shipping material from toner cartridge Description A toner cartridge shipping lock is installed.

I have a great place to purchase fuser so let me know if you nee contact info! Turn the product power on. If you are using a surge protector, remove it. weblink For others reading not to long ago I replaced a fuser for a scheduled PM cycle and got called back a week later for a similar problem.

© Copyright 2017 postmapper.com. All rights reserved.