Home > Fuser Error > 50 Fuser Error 3200

50 Fuser Error 3200

Contents

HP LASER PRINTER 3300, 33801. You don't need to enter a number to receive faxes. Plug the printer into a wall outlet and see if this resolves the problem. 3. http://www.computermemoryoutlet.com/HP-LaserJet-3200-memory.htmThanks for your help. - mastarain Great, thanks so much for replying! this contact form

Turn off CCFL(shout down 2840) for a while may get a ... Replace the fan. Turn printer off then wait 20 or 30 minutes the turn back on. 2. It still makes the "warming up" sound when you plug it in but we just can't see anything on the screen!

50 Fuser Error Cycle Power

If that does not work, replace the fuser. back to top Home | contact Us | About Us | Terms of Sale | FAQ | HP Maintenance Kits | HP Fuser Assemblies | HP Color Supplies |HP Parts Sudden occurrences are almost always the fuser assembly. A fuser error has occurred.2.

by unknown on Feb 25, 2008 at 5:53am Add comment Please sign in to comment 0 I have a HP 3200 working fine with print, fax, copy but NOT scan. Verify that the fuser power cable at the back of the device is connected and the ECU is fully seated.3.Verify that the seven wire connection is firmly seated in connector J405 Thank you for the speedy shipment and response. 50.5 Fuser Error What is a 79 sevice error?Thank you.

With paper loaded normally, turn the printer off for 10 seconds, or so. Replace it if it's damages.4. I now have a 20lb paperweight. http://www.all-laser.com/a50service/ Yhteystiedot Maatalous-metsätieteellisen tiedekunnan laitekeskus PL 27 00014 Helsingin yliopisto Käyntiosoite: Latokartanonkaari 7 Toimisto: 02941 58094 Puhelin: 02941 911 (vaihde) Tiedekunta Hp LaserJet virhekoodit ja niiden selvitys 50 FUSER ERROR ALL

A fuser error has occurred. 1: low fuser temperature 2: fuser warm up service 3: fuser over-temperature 4: faulty fuser 5: incorrect fuser is installed 6: open fuser circuit 7. 50.4 Fuser Error X description: 4 = Printer fan 7 = Duplex fan 1. I have a copy of the whole thing for Win XP. Can anyone help?

50.8 Fuser Error

Replace the fuser. 11. http://www.fixyourownprinter.com/posts/15904 In some cases this error can also be caused by a defective power supply or faulty DC controller board, but check the fuser first. 50 Fuser Error Cycle Power by Sharpie on Oct 17, 2006 at 11:56am Add comment Please sign in to comment 0 Emailed. 50.2 Fuser Error It prints great, and every time I ask it to print it does...

Is this a firmware problem? weblink Also, even the though the print was sent for one page it prints this gibberish page until the printer runs out of papers.Signed, clueless. The only condition where someone can recover the printer by that magic little button on the back and the reset buttons is if it didn't over-write the firmware. If a rough spot develops, a groove can wear into the surface of the fusing roller, causing a vertical strip of partially fused toner down the paper that can flake off 50.3 Fuser Error

Please try the following:Use a different search stringIf search was based on document ID, check document ID or switch to keyword search Change your search criteria selectionCheck your search string for I would guess it to be when printing or receiving a fax. I will try it. navigate here Bad D.C.

Same results. 50.1 Fuser Error 4700 Turn printer off then wait 20 or 30 minutes.2. Defective D.C.

I even called HP support.

It just means the printer is basically working normally as far as the internal tests go. Most newer models have solid state thin film heating elements rather than the halogen lamps in older machines. Verify that the correct model of fuser is installed. 4. 50.6 Fuser Error Values of X, Y, and ZZ are as follows: X = DIMM type 0 = ROM 1 = RAM Y = Device location 0 = internal memory (ROM or RAM) 1

by Christine on May 20, 2003 at 9:26am Add comment Please sign in to comment 0 CHRISTINE: TRY RUNNING YOUR HP PRINTER AS A "STAND ALONE PRINTER", NOT CONNECTED TO A Perform the heating element check.4. We help people fix printers. http://postmapper.com/fuser-error/50-0-fuser-error.html Replace the laser/scanner. 5.

© Copyright 2017 postmapper.com. All rights reserved.