Home > Fuser Error > 4v Error 50

4v Error 50

Contents

Also, can I get some instructions on putting in the rollers. Reply With Quote 01-15-2009,04:38 PM #6 GG**2 View Profile View Forum Posts View Blog Entries View Articles Junior Member Join Date Jan 2009 Posts 3 Yes, the printer is plugged into If the error persists, replace the heating element.6. Verify that the correct model fuser is installed in the device. 9.

Maladjusted or bent Switchback assembly. X=4 Faulty fuser. There is a link for checking the lamp continuity before ordering. It must be more serious than just a fuser related issue.

50.0 Fuser Error

Worn pick up rollers and/or separation pad. replace fuser 2. 50 reset procedure, turn machine off wait 10 minutes, should reset 50 code, if not, remove formatter board and short leads C202 on DC controller. Defective fuser. 3.

Move the printer to another power source and disconnect it from any UPS or surge protector3. Bad fuser ass'y5. I went through and checked both fusers. 50.0 Fuser Error Hp Laserjet P1007 There must be a relay in the supply that turns the fuser on at a certain point in the power up cycle.

Reply With Quote 09-09-2011,10:41 PM #9 woodss View Profile View Forum Posts View Blog Entries Visit Homepage View Articles Senior Member Join Date Aug 2004 Location Victoria, Australia Posts 228 The 50.0 Fuser Error Hp Laserjet P1102 by unknown on Aug 12, 2004 at 11:46am Add comment Please sign in to comment 0 A 50 SERVICE indicates a problem with the fuser. If it is not within the proper range, replace the fuser. http://printertechsforum.com/forum/showthread.php?2534-Laserjet-4-error-code-quot-50-Service-quot-help I will have purchasing call in an order.

Turn the printer off and allow it to cool down for a minimum of 20 minutes.2. 50.0 Fuser Error P1108 Computer is powered off Unseated or defective MIO card 5P Indicates an abnormal connection break occurred while transferring data from the computer 41 Error (Temporary print engine failure) All printers Reset Thanks, GG**2 Reply With Quote 01-06-2009,12:33 PM #2 Big Al View Profile View Forum Posts View Blog Entries View Articles Senior Member Join Date Apr 2008 Location Winchester Virginia Posts 520 Hold down the front panel button to display the error LED code.

50.0 Fuser Error Hp Laserjet P1102

If the message persists, reseat the fuser. http://www.advancedlaser-hp-error-codes.com/error_50.htm Turn off printer for 20 minutes (to allow internal error circuit to reset) and try again. 50.0 Fuser Error Turn duplex unit off when using envelopes 57 Error III, IIID only 57-1 error. 50.0 Fuser Error Hp Laserjet P1108 The connector is in the front end of the supply.

Replace DC Controller PCB. Replace the fuser ass'y 3. Any Suggestions as to what a "50 Service" code means? Incorrect cable hookup or bad I/O port in computer. 50 Fuser Error Hp Laserjet 3050

Use saved Parts Lists as templates to create new lists. You may have to register before you can post: click the register link above to proceed. What now? Incompatible memory card in front slot 57-2 error.

If you have a meter you could check for 110VAC fuser voltage at the power supply. 50 Fuser Error Hp Laserjet 3052 The only suitable capacitor I had was a 40V unit, considerably larger than HPs original capacitor. If a surge protector is being used, remove it.

When I turn on the unit, there is 110V present when first turned on.

Turn the printer off and then on. 3. Possibly a cooling fan or the fuser itself needs replacing. To check the fuser, turn the printer off and remove the fuser. 50 Fuser Error Hp Laserjet 3055 Powered by vBulletin Version 4.2.2 Copyright © 2016 vBulletin Solutions, Inc.

Look for bent pins or debris. HP IIID, annoying "Service Error 50" problem 13. Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person. HP COLOR LASER PRINTER 4600, 5500 ERROR 50.XX1.

Power printer OFF!!) (On LJIID short C216 on DC controller PCB to bypass 20 minute delay. Defective D.C. back to top •HP LJ 4/4M & HP LJ 4+/4M+/5 On the HP Laserjet 4/4M/4+/4M+, most suspect is the halogen lamp. FAQ Home Search Printer and Photocopier Troubleshooting and Repair Collection : HP LaserJet 4 - intermittent error code ..

Turn the MFP off, and allow it to cool. 3. Unplug the red/black two wire cable first. controller HP LASER PRINTERS 4, 4+, 5 1. back to top Home | contact Us | About Us | Terms of Sale | FAQ | HP Maintenance Kits | HP Fuser Assemblies | HP Color Supplies |HP Parts

Replace engine board. Plug the printer into a wall outlet and see if this resolves the problem. 3. Reply With Quote 09-09-2011,10:28 AM #8 mama26kiddos View Profile View Forum Posts View Blog Entries View Articles Junior Member Join Date Sep 2011 Posts 1 replacement printer Is there a good If error goes away replace SIMM Replace formatter PCB 5P SIMM malfunction.

Short C202 on the DC controller PCB to bypass the 20 minute delay, power printer OFF!!) 4V, 4L, 4P, 5P Verify fuser is properly seated Replace fuser 51 Error (Loss of

© Copyright 2017 postmapper.com. All rights reserved.