Home > Fuser Error > 4345 Fuser Error

4345 Fuser Error

Contents

The following is some introduction "How to fix fuser unit error of HP LJ-mfp-m4345": 1. Mirisa: Hi friend ! Remove and reinstall the envelope feeder. The MFP limits the number of folders that can be established. Check This Out

If the accessory uses cables, disconnect and reconnect them. Retype the user name and password. Check for a warped or wrinkled surface on the pressure roller and the gears out. Contact the network administrator. http://www.fixyourownprinter.com/posts/51921

Hp Laserjet 4345 Fuser

SANITIZING DISK % COMPLETE Do not power off The hard disk is being cleaned. Remove the paper from the document feeder output bin. Remove the remaining media from the document feeder and close the document feeder cover. Recommended action Turn the MFP off, and then turn the MFP on.

The folder you have entered is not a valid folder. Does anyone know if there is a error reset for this code? Replace the print cartridge. Hp 4345 Fuser Part Number Turn the MFP power on.

For information about replacing the staple cartridge, go to http://www.hp.com/support/ljm4345mfp for additional information. Fusor Hp 4345 Message type Description Status messages Status messages reflect the current state of the device. If this message persists, contact an HP-authorized service or support provider, or go to http://www.hp.com/support/ljm4345mfp .

The Digital Sending Service at does not service this MFP.

Squeeze the blue fuser release tabs 4. Hp 4345 Maintenance Kit The Open heat error occur when When warming up, it has been lower than 60*C over 35 seconds and on the staus window of computer or LCD screen of printer (if Error executing Digital Send job. If this message persists, contact an HP-authorized service or support provider, or go to http://www.hp.com/support/ljm4345mfp .) 51.XY ERROR To continue turn off then on Explanation A temporary printing error has occurred.

Fusor Hp 4345

All Rights Reserved. https://www.orionmarket.com/product_error/3013/HP/HP-4345/50.x-fuser-error/ Also, the DC controller or power supply are other options but after working on several hundred of these machines and never replacing one I'll say that very rarely happens. Hp Laserjet 4345 Fuser Reconfigure the size in a tray so that the MFP will use a tray that contains the size required for the print job. 50.5 Fuser Error Hp 4250 As a safety precaution wait 30 minutes for the fuser to cool before proceeding.

If this message persists, contact an HP-authorized service or support provider, or go to http://www.hp.com/support/ljm4345mfp .) User name or password is incorrect. http://postmapper.com/fuser-error/924-fuser-error.html You can check continuity across of halogen lamp, if it have problem then replace halogen lamp. When your printer occurt Over heat error, the printed page will be appear ghost occurs at 82 or 92 mm intervals and on the status window of coputer shown on: Over If the message is not cleared, turn the MFP off, and then turn the MFP on. Hp Laserjet 50.2 Fuser Error

Job failed. The follwing are the most common problems that can cause a Low heat error. by moe on Nov 13, 2007 at 6:00pm Add comment Please sign in to comment 0 It's all OEM parts (factory HP sealed box) we just buy through a re-seller.Another fuser this contact form LDAP Server is not responding Contact administrator Load envelope feeder The LDAP server has exceeded the time out value for an address request.

Type the user name and password, or contact the network administrator. 50.4 Fuser Error Your cache administrator is webmaster. I'll post results in a couple days when the new fuser unit (#3) arrives.

Transcript The interactive transcript could not be loaded.

Either of those fuser part #'s will work; but any other part# will trigger a 50.4 error code. Was it from HP or somewhere else?I didn't understand the hostility either. Try to get a second replacement fuser with the correct part#; that should fix it. Hp 4250 Fuser Kit The function of fuser unit - Thermistor bar (or halogen lamp) of fuser clusters created temperatures up to 180 * C for fusing toner powder.

Please enter correct login. If Auto-Continue is set on the menus, the device will continue normal operation after an auto-continuable error message appears for 10 seconds. Recommended action Follow the instructions in the onscreen dialog box. 13.JJ.NT JAM INSIDE TOP COVER AREA Explanation Media is jammed in the top cover area. http://postmapper.com/fuser-error/922-fuser-error.html If the message is not cleared, turn the MFP off, and then turn the MFP on.

I'm following dmzcompute's advice, I tried the "High1" setting, but the fuser isn't heating up at all.I can see some obvious damage to the first fuser tried (the one that worked HP 4300 Laserjet 50.1 Fuser Error Message For Low Temperature 50.9 Fuser Error - HP Color LaserJet 3000, 3600, 3800, CP3505Parts and Supplies StoreBrother Parts / Supplies Canon Parts / Supplies Turn the MFP off, and then replace the DIMM that caused the error. With   the 50.2 fuser error the machine has reached a fuser warmup error.

The user name or password was typed incorrectly. One or more of the e-mail addresses is incorrect. Order cartridge The number of pages remaining for the print cartridge has reached the low threshold. Generated Thu, 29 Sep 2016 13:49:14 GMT by s_hv972 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection

Contact administrator.

© Copyright 2017 postmapper.com. All rights reserved.