Home > Fuser Error > 4050 50.2 Fuser Error

4050 50.2 Fuser Error

Contents

Privacy Policy Terms of Use Search Fixya Press enter to search. The manual recommends turning the printer power off, wait a moment, then turn the power back on (reset). This is due to the many different formatter board revisions. Sign in to make your opinion count. have a peek here

Source(s): Graeme · 4 years ago 0 Thumbs up 0 Thumbs down Comment Add a comment Submit · just now Report Abuse If you experience a "50.2" fuser error while using Who on earth told you to cut the film down!!! Sign in Share More Report Need to report the video? I did not notice that the connection had slipped out of place, probably when I was rotating the gears to view all of the fuser roller. http://www.printertechs.com/printer-troubleshooting/11-50-2-fuser-error

50.2 Fuser Error Hp Laserjet 4050

BrokenPrinter1 29,146 views 8:28 how to install and remove pickup rollers on a hp 4000 4050 4100 4050n 4100n RB1-8865 - Duration: 4:25. If the message persists, reseat the Fuser. Add × Loading... Last thing to try is leaving the machine unplugged for 10 to 20 minutes and then plug back in and try again which is what HP recommends in the service manual

Sign upLog inPinterest • The world’s catalog of imagesExplore 4100 4200, 2 Error, and more!PrintersSaveLearn more at printertechs.com50.2 fuser error HP LaserJet 4000 4050 4100 4200 4300More 1Terry GEbauerStuff to BuySaveLearn It has been designed to work with HP LaserJet 4000 and 4050 Printer LaserJet printer series. I have a hp4000 tn and i am getting this error message. 50.2 Fuser Error P3015 I'd wait until towards the end of the auction to bid on it.

The two connections I checked were on the left side. I have ordered kits from Fix Your Own Printer before and was very pleased with the service and results. - MorrisWood 0 I have an hp 4100 laser reporting 50.2 fuser Make sure the brown connectors are seated properly.

Not that hard. 2 screws and a couple of connectors and it comes off.

x SERVICE ERROR communication related issues the codes following the 49. 50.2 Fuser Error 4250 Loading... Fuser webs(belts) gradually get consumed after about 100,000 prints. I have purchased a maintance kit from hp directly when it said to maintence the machine and now the fuser error message is appearing.

50.2 Fuser Error P4015

Replacement kit available here for about $40. http://fixyourownprinter.com/posts/30652 Laser Jet printer failure with 13.1c.00 error indicates a paper jam in the fuser. 50.2 Fuser Error Hp Laserjet 4050 HP 4050 13.1 PAPER JAM OR 13.2 PAPER JAM Paper delay jam at paper feed area (13.1). 50.2 Fuser Error Laserjet Pro 400 by moe on Nov 12, 2005 at 6:35pm Add comment Please sign in to comment 0 I believe Australia uses 240 Volt 50 HZ AC power.The US uses 120 Volts 60HZ.There

If that does not work, replace the Fuser.To check the Fuser, turn the printer off and remove the Fuser. navigate here The right edge of the fixing film on the fuser roller had deteriorated, resulting in jagged edges in the film. (That end looked browned, like the heating element was hotter at turn on the printer it says to you clear jam in tray one when there is no jam at all Apr 30, 2014 | HP LaserJet 4200 Printer 0 Answers how Corporal: An expert that has over 10 points. 50.2 Fuser Error Hp 4700

BrokenPrinter1 17,067 views 4:25 How to refill HP LaserjetPro P1102 Printer with CE651A cartridges - Duration: 9:47. by wlulham on Oct 27, 2005 at 6:23am Add comment Please sign in to comment 0 wlulham, I am a little confused but am reluctant to pay for someone to fix! HP 4000/4050 Fuser Assembly RG5-2661-000 HP Fuser for LaserJet 4100Troubleshooting The  HP Laserjet 4000, 4050, and 4100 50.2 Fuser ErrorFirst thing to try in troubleshooting the HP Laserjet 4000, 4050, and Check This Out Thanks by unknown on Oct 27, 2005 at 8:30am Add comment Please sign in to comment 0 Yes the 50.2 is fuser warm up error, so it has to be replaced.

by MorrisWood on Jul 27, 2005 at 1:55pm Add comment Please sign in to comment 0 Remember you can order the fixing film from this site and help keep these handy 50.2 Fuser Error Hp 5100 Once the door is off, you're looking straight at the fuser. Our printer technicians have the knowledge and technical ability to repair LaserJet 4050 printers on the first visit.

It's that simple.

What next do I do? If it is not within the range of 200kW to 500kW, replace the Fuser. What does that mean Posted by mjv48317 on Mar 31, 2010 Want Answer 0 Clicking this will make more experts see the question and we will remind you when it gets 50.1 Fuser Error It takes a lot of time and effort to put these articles together.

Turn the printer off for about 5 minutes. Notify me of new posts by email. What are the odds of that? http://postmapper.com/fuser-error/50-01-fuser-error.html Step 2: Please assign your manual to a product: About Advertising About Us Blog Careers News & Media Help Contact FAQ Partners Privacy Policy Terms Community Forums Recent Q&A Top Experts

Measure the resistance between the Fuser connectors J132-1 and J132-2.   If it is not within the range of 200k  Î© to 500kΩ, replace the Fuser. 3. Flip it to the gear side (the left side) and press inwards on the fuser tab to make sure it is fully clicked in place. We specialize on HP LaserJet 4000/4050/4100 printer repair with 13.01.00 paper jam service error. Need to access my aunts yahoo mail on my pc how dose she do that i have a printer she dose not and she needs 1?

© Copyright 2017 postmapper.com. All rights reserved.