CAUTION: Static electricity can damage DIMMs. Action Contact HP or an authorized service provider. Answer questions, earn points and help others Answer questions Manuals & User Guides PDF Manual . I used a propane torch and heated the card directly for aprox. check over here
Power up, if problem is still there put the card in the other EIO slot. Replace your jet direct card with one that you know is good.Test to see if either of these resolves the issue.The problem is usually a faulty card. You can try rebooting/resetting which can clear it but usually means a trip to the hp repair shop. If the Error Code reappears, then use the above information to troubleshoot the problem.
Remove the Hard Disk Drive (if installed) and make sure that the EIO card is installedcorrectly by pushing it firmly inwards and checking that the two installation screws are completely tightened. Sign in to make your opinion count. The second slot might be a hard drive but is usually open. 79.00fe Printer Error Hp 5100 You can also turn the jam-clearing wheel that is located on the side of the fuser to attempt to eject the jammed paper.
Action Try to remove the sealing tape, for instructions see the following list: Lift the printer top cover. Feb 18, 2014 | HP LaserJet 4600 Printer 1 Answer Error code 40.0 A connection with the card in EIO slot X has been abnormally broken.1. NOTE: For more information and troubleshooting steps, refer to the document HP Jetdirect Print Servers - 80, 81,82, 86, and 87 Service Errors (bpj05423). http://www.fixya.com/support/t10753560-81_0180_eio_1_error If the above action does not solve the issue, contact HP or an authorized service provider.
Ensure that it is not damaged and that it moves freely. Hp Laserjet 4250 Error Codes If it works, take the two screws and the cover and use it to cover EIO 1. the EIO card in slot 3 is probably faulty. These messages typically alternate with the “Ready” or “Status” messages and remain displayed until the (Select) is pressed.
HP is replacing them free until October under a Service Note. n The Service Configuration Print þ n The Current configuration sheet. 81.0180 Eio 1 Error Hp 5500 n If the Error code continues to appear, switch the Printer OFF. Eio Card Hp Printer n If the Error code continues to appear, switch the Printer OFF.
If the above action does not solve the issue, contact HP or an authorized service provider. X Description 3- EP cartridge fan, right side (HP LaserJet 4300 only) 4- Main cooling fan, left side Action Turn the printer power off and then turn the printer power on. Move the Jet Direct card from port 1 to port 2 on the printer. Your answer needs to include more details to help people. Eio 1 Error Hp Laserjet 4600
Remove the toner cartridge to check for paper in the paper path, remove all found, then reinstall the cartridge. If both the EIO slots do not recognize the card. Remove all EIO devices and firmware DIMM if installed. If the above action does not solve the issue, contact HP or authorized service provider.
The second slot might be a hard drive but is usually open. Jetdirect 620n Most likely it's a JetDirect card. You can't post answers that contain an email address.
If you get another EIO error the card is probably bad. If the above action does not solve the issue, contact HP or an authorized service provider. If loose toner falls into the printer, it might cause temporary problems with print quality. Figure 9: Removing the jammed paper Make sure that the paper is flat in the tray at all four corners and below the maximum-height indicators.
This causes static electricity, which can cause paper jams. Remove all non-HP paper-handling devices. Figure 47: Removing the cover Open the DIMM-access door by pulling on the metal tab. Press (Select) to select PRINT CONFIGURATIONCheck if the I/O card is on ready state.
top 8X.YYYY EIO ERROR Description The EIO accessory in slot [X] has encountered a critical error. [X] description: 1 = EIO slot 1 - The printer detected an error with the If a jam message persists, it is possible that paper is still jammed in the printer. Switch the Printer ON again. There should be 2 EIO slots.
If the issue does not reoccur, with the known good duplexer, replace the old duplexer. EIO is the External Input Output slot that is on the formatter of the printer. Figure 27: Removing paper Verify the deflector in the printer is working correctly. Edit Close Save changes Attachments: Added items Uploading: 0% my-video-file.mp4 Complete.
Action Press the (Select) button to process the page. Here's Why Members Love Tek-Tips Forums: Talk To Other Members Notification Of Responses To Questions Favorite Forums One Click Access Keyword Search Of All Posts, And More... Include an image. If you are still getting the error pull the card and power up the device with out the card installed.
If a print job is sent and the stapler is jammed or is out of staples, the job will still print as long as the path to the stacker bin is The EIO 1 means it is now in slot 1. If the error does not clear, turn the printer power off and then turn the printer power on. CAUTION: Do not fan the paper.
Tip: The max point reward for answering a question is 15. 0 characters Video Photos Link Replacement Parts Add Upload Upload × × Draw a box over the problem!! Slide the print cartridge into the printer as far as it can go.