Home > Error Hp > 60.2 Error Hp 4250

60.2 Error Hp 4250

Contents

Do not attempt to grasp the paper as it exits the duplexer to the output bin. Reply With Quote 12-07-2009 #8 prntrfxr View Profile View Forum Posts Private Message Dangerous with Tools 1,000+ Posts Join Date Apr 2008 Location Living in Exile Posts 1,670 Post Thanks / Hope this helps. If so, reinstall the duplexer. his comment is here

Accompanied by 13.X or 60.X Error. 4. Turn the printer power off and then turn the printer power on. Then reinstall the paper and try again. Clicking noise after tray installation motor spins, but paper level indicator is not moving. http://www.partsnow.com/news/ImagingNow/vol2iss1/clearing-error60-2_onhp

49.4c02 Error Hp 4250

Action Press the (Select) button to continue. Remove the duplexer if installed. If the job prints, go back to the first program and try printing a different file. (If the message appears only with a certain program or print job, contact the software Action If the incorrect size was selected, cancel the job or press the Help (?) button to gain access to help.

Figure 29: Removing duplexer Remove any paper on top of Tray 2. (You might need to reach inside the printer.) Figure 30: Removing paper from Tray 2 Slowly pull any paper NOTE: A loss of data will occur. you can also watch the paper level indicator on the front of the tray to see if it moves. 3. 51.10 Error Hp 4250 Also check J1506 on the corresponding HCI PCA.

You can also watch the paper level indicator on the front of the tray to see if it moves. 4. For enterprise products go to Hewlett Packard Enterprise.© Copyright 2016 HP Development Company, L.P. Disconnect all optional paper handling accessories and try printing again. You might be able to print pages that are more complex if you add memory to the printer.

Look for the jam in another location, contact HP, or contact an authorized service provider. 49.4c02 Service Error Hp 4250 Types of messages Status messages Status messages reflect the current state of the printer. Remove all non-HP paper-handling devices. Push the blue levers upward and pull the fuser straight out of the printer.

60.02 Error Hp 4250

Replace the D.C. http://www.advancedlaser-hp-error-codes.com/error_60.htm CAUTION: Static electricity can damage DIMMs. 49.4c02 Error Hp 4250 Action Remove any jammed media from the paper path. 57.04 Error Hp 4250 If the message persists, contact HP Customer Support.

Thank you. http://postmapper.com/error-hp/49-4c02-printer-error-4250.html Reply With Quote 12-04-2009 #6 Deano View Profile View Forum Posts Private Message Technician Join Date Oct 2009 Location St helier Posts 21 Post Thanks / Like Thanks (Given) 0 Thanks Replace tray 2 lift drive ass'y3. Check the configuration of the EIO (HP Jetdirect card) and the host computer. 59.40 Error Hp 4250

Figure 60: Sliding tray into printer After performing the actions above, press (Select) The page containing the error will automatically be reprinted if jam recovery is enabled. (Or, you might want Feedback? Figure 31: Removing paper from duplexer Insert the optional duplexer into the printer. weblink If the above action does not solve the issue, contact HP or authorized service provider.

Figure 41: Installing rear-output bin Plug the power cord into the printer. 49.4c02 Service Error Hp 4250 Printer For Tray 2 and Tray 3, verify that connector J324 on the DC Controller PCA is firmly seated. If the above action does not solve the issue, contact HP or an authorized service provider.

If possible, try to use a fresh ream of paper and do not fan the paper.

If the tray has no problem then replace the lifter motor to resolve the error 60.2 message. Its 50 cents from HP. If jammed, paper is present, remove it. 50.2 Fuser Error Hp 4250 Pick-up Assembly Loose The pick-up assembly is missing the bushing, gear, or both, which causes the assembly to be loose.

A:  When your hp laserjet 4250 perform printer maintenance message appears on your display panel it is time to install a hp laserjet 4250 maintenance kit (q5421a).  The printer is programmed Life should NOT be a journey to the grave with the intention of arriving safely in an attractive and well-preserved body, but rather to skid in sideways - Coke in one Yesterday I was working on a 4200 that was making a loud ratcheting sound. check over here This connector is for the lift motor. 4.

top top 69.X PRINTER ERROR To continue turn off then on Description The optional duplexer is not functioning. If one of the feet isn't on the surface the bottom of the machine pushes up on the tray and causes it not to lift properly.Another thing I notice is that alternates with 59.XY PRINTER ERROR To continue turn off then on 59.2 MAIN MOTOR ROTATION ERROR 59.4 EP MOTOR ROTATION ERROR (HP LaserJet 4300 only) 60.X PRINTER ERROR 62 NO SYSTEM If the above action does not solve the issue, contact HP or an authorized service provider. 13.XX.YY JAM IN TOP COVER AREA Description Paper has jammed in the top-cover area of

Some Help topics include animations that appear on the control panel to show how to resolve an error.

© Copyright 2017 postmapper.com. All rights reserved.