It processes information and then directs it to the proper component. Press the SELECT button to continue. 3. f the message persists with different software applications and print jobs, disconnect all cables to the printer that connect it to the network or PC. Vice President: An expert whose answer got voted for 100 times. Check This Out
Press the Checkarm button twice until the letter S is highlighted. See Figure 1. Steps 1 Print a configuration page and a menu map. 2 Turn off the printer. 3 Remove all formatter accessories (EIO cards, hard drive, DIMMs, etc.). 4 While turning on the Posted by laxmanchowdary at 10:42 AM 2 comments: Email ThisBlogThis!Share to TwitterShare to FacebookShare to Pinterest Monday, July 21, 2014 Scan takes too long time.....Fallow the below steps The resolution might http://h30434.www3.hp.com/t5/Inkjet-Printing/Error-49-4C02/td-p/687293
The fact that printing to a virtual device, and then resending, points to timeouts as a reason. WTF does that mean???? Figure 1: Lifting up the daughter (interconnect) board on the formatter 1 - Black retaining tab underneath the formatter Reseat the daughter board. If the message persists with different applications and print jobs , disconnect all cables to the printer that connect it to thenetworkor PC.
See Figure 2. Flash the latest availablefirmwareto the printer. by unknown on Dec 3, 2009 at 7:51am Add comment Please sign in to comment 0 After following all this troubleshooting suggestions, I fixed this error by un-checking a box in 49.4c02 Error Hp P3005 Turn the printer on and perform a cold reset. (Turn the printer on and when the printer shows the memory counting press and hold the 6 key until all three lights
For a PSdriverprinter:1. If the job prints, go back to the first program and try printing a different file. Can be associated with connections on routers, switches and even ports. 9. http://www.fixyourownprinter.com/posts/30528 The printer will perform a cold reset and then continue its power-on sequence.
Some basic problems that can cause these errors are file specific issues, network connections, driver settings, or operating system related issues. 49.4c02 Error Hp 9050 Becomean Author! Got a reply from HP support to verify my fix. On the 5500 the JetDirect Card can cause the problem.Sometimes upgrading the JetDirectfirmwarehelps.If it continues replace the JetDirect card (usually a 615N).
Add × Loading... http://printertechsforum.com/forum/showthread.php?2445-HP-LJ-4100-with-error-code-49-4c02 Powered by Mediawiki. 49.4c02 Error Hp P3015 The following procedure should allow you to get past the reported boot progress hang or the 49.4C02 error.CAUTION when performing a cold reset you will delete network settings and printer settings.NVRAM 49.4c02 Error To Continue Turn Off Then On by unknown on Apr 27, 2007 at 7:13am Add comment Please sign in to comment 0 http://www.fixyourownprinter.com/forums/printer/46901#1 by Stephen on Apr 27, 2007 at 10:36am Add comment Please sign in to
by unknown on Jun 2, 2011 at 8:17pm Add comment Please sign in to comment 0 This issue can be solved this the rom update..http://www.techieshelp.com/error-49-4c02-on-hp-printer/ by unknown on Sep 19, 2011 his comment is here Flash the latest available firmware to the printer.For parts pricing and availability [email protected]://www.metrofuser.com/ Comments 4 # [WJ]: HPLJ 49.4C02 error 2015-08-18 06:30 pm Turn off the printer, turn on the printer Adjust the margin settings, if possible. This log can be printed if the printer is operational or even viewed via the printers display panel. 49.4c02 Error Hp 4015
You have to go to the computer where the print was originally requested from and cancel out all print files in the print que. To continue printing try to: 1.Turn off the printer2.Disconnect the data ornetworkcable3.Clear the print queue4.Turn the printer back on5.Re-connect the data ornetworkcable6. Or just drag it here! this contact form If the message appears only with a certain software application or print job, contact the software vendor for assistance. 4.
Click "Add" to insert your video. 49.4c02 Error Hp P4014 If the 49 error returns turn the power off, unplug the power cable, disconnect all network cables, and remove the HP Jetdirect card (or any third-party devices), if installed. Larger printings tend to result in this error as well.
Wait at least 30 seconds before plugging the printer back in directly to a wall outlet. The restore factory settings command which can be accessed from thecontrol panelof these printers can be used, but in doing so all the configuration settings will be reset to factory defaults. Afterwards, restart your printer. 49.4c02 Service Error Hp 4350 Reply 0 0 cpubugs Student Posts: 1 Member Since: 10-13-2014 Message 7 of 8 (209,448 Views) Report Inappropriate Content Re: Error 49.4C02 Options Mark as New Bookmark Subscribe Subscribe to RSS
If it comes up toREADY, print a configuration page. or it's affiliates. CAUTION when performing acold resetyou will deletenetworksettings and printer settings. navigate here The 49.4C02 error usually follows a paper jam.
If the job prints, go back tothe first application and try printing a different file. In some instances after upgrading a LaserJet M-series MFP firmware upon rebooting the 49 error will occur. Learn how. This was on 3 of 30 printers on our network.
If in a queue, look at the jobs in the queue, look at the job which says it is printing, look at the user, delete the job from the user's computer. Release the check button when the Ready, Data, and Attention light are on steady. Let me know if you need anything else. PRINTERUPGRADING FROMUPGRADING TO M3027mfp, M3035mfp20071211 48.051.1 or earlier20080405 48.061.8 or later M4345mfp 20071211 48.051.1 or earlier20080405 48.061.8 or laterM5025mfp
Posted by laxmanchowdary at 5:33 AM No comments: Email ThisBlogThis!Share to TwitterShare to FacebookShare to Pinterest RFU Load Error Resend RFU Message On HP LaserJet 4240 4250 4350.. If in a queue, look at the jobs in the queue, look at the job which says it is printing, look at the user, delete the job from the user's computer. Turn the printer on. I just did 2 more last night and plan on doing this to all over the next month.