Home > Error Codes > 93 Maxima Error Codes

93 Maxima Error Codes

Contents

For example, if the red diode flashes once and then flashes twice rapidly this should be interpreted as code 12. Close Yeah, keep it Undo Close This video is unavailable. Here is the kicker. ibemerson is offline Quote Quick Reply post #7 of 14 Old 05-24-2004, 05:55 AM bok Registered User Join Date: Oct 2003 Location: ootah Posts: 36 Mentioned: 0 Post(s) Tagged: check over here

Code 42 (4 red flashes, 2 green flashes) Fuel temperature sensor (1988 models) The fuel temperature sensor circuit is open or shorted. Join Date: Jul 2002 Location: Northern VA Posts: 6,149 Mentioned: 0 Post(s) Tagged: 0 Thread(s) Quoted: 4 Post(s) Thanks: 3 Thanked 43 Times in 30 Posts iTrader: 1 reviews (Thread Starter) I thought it may be useful. Make sure LEDs do not flash for 5 minutes when racing or idling the engine. http://www.troublecodes.net/nissan/

Maytag Maxima Error Codes

Make sure the RED LED turns on when depressing the gas pedal. Reconnect harness and recheck continuity. Tim Quirk 2,078 views 1:03 What to do when the Check Engine Light Comes On - Duration: 3:40. Thanks.

Were you going to ask a question? 3. About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new! If the LED does not flash, check the sensor's circuit. Maytag Maxima Error Codes F01 E02 Insert a flat bladed screw driver in the hole next to the slot where the two lights are located.

Could the ecu throwing 55 have anything to do with this? Maytag Maxima Error Codes E01 F09 Quote: Rules: 1)Search search, search, search. Fig. 1 Checking ECU trouble codes. http://www.nissanclub.com/forums/general-nissan-altima-discussion-1993-2001/126968-ecu-self-diagnostic-modes-trouble-codes.html To check the codes, turn the ignition switch on, but do not start the engine.

tbs95111-01-2004, 07:22 PMthe '93 Maxima I'm working on has no injector pulse on cranking, it sparks fine, and will start with some cranking on starter fluid, but not on its own, Maytag Maxima Dryer Error Codes Nissan UD Diesel ID-TICS System Place diagnostic switch in the Off position. If the RED LED stays on or off above 2000 RPM, complete the diagnostics before beginning repairs. When the LEDs are blinking one at a time, red is the 'tens' place, and green is the 'ones' place.

Maytag Maxima Error Codes E01 F09

Also run a continuity check between wires to make sure they aren't melted together. 4. The ECM will then go back to the lowest numbered code and repeat the cycle. Maytag Maxima Error Codes Inspect the harness for dust and clean if necessary. Maytag Maxima Error Codes F06 E02 After the LED flashes 5 times, turn the dial fully counter clockwise. 4.

Email Address: OR Log-in User Name Password Remember Me? http://postmapper.com/error-codes/510-canon-error-codes.html The trouble codes will be displayed by the flashing Engine Control Lamp and the Overheat Warning Lamp and the Overheat Warning Buzzer. Password: Confirm Password: Email Address Please enter a valid email address for yourself. Rating is available when the video has been rented. Maytag Maxima Error Codes E01 F08

Turn the dial on the ECU fully clockwise. Both lights will blink together just like before. Forums Maxima.org Feedback/Suggestions New Member Introductions Maxima Discussions General Maxima Discussion 8th Generation Maxima (2016-) 7th Generation Maxima (2009-2015) 6th Generation Maxima (2004-2008) 5th Generation Maxima (2000-2003) 4th Generation Maxima (1995-1999) this content Diagnostic Display Code 0–1 should be indicated.

They are independent publications and are not affiliated with or endorsed by Nissan or Infiniti. 93 Nissan Maxima Heres a link to all the OBD II software available http://www.troublecodes.net/technical/scaninfo.shtml Fixed applicable model 1995-1996 year info, thank you for the original post. Please enter your desired user name, your email address and other required details in the form below.

Check the pin terminal at ECU for bends and remove them as necessary.

any help on this one would help me out alot!!! -Steve efield43 is offline Quote Quick Reply Reply Nissan Forum > Truck & SUV Gear in this threadEngine Control Instead of turning the needle to it's max, simply lift the needle over the zero peg and let it fall to rest. Apparently only the 93 & 94 models used the 2 digit code format. 93 Nissan Maxima Parts sdotcarter 6th Generation Maxima (2004-2008) 2 09-02-2015 09:53 PM « Previous Thread | Next Thread » Thread Tools Show Printable Version Search this Thread Advanced Search Posting Rules You may not

Reconnect harness and recheck continuity. Up next How to pulll engine codes without a scan tool "response video" - Duration: 2:47. uncnissan2004 is offline Quote Quick Reply post #6 of 15 Old Jun 17th, 2004, 07:28 AM mastertech NissanForums Newbie Joined: Jun 2004 Location: Charlotte, NC Posts: 4 light screw have a peek at these guys If LEDs do not flash for 5 minutes, turn engine off.

Please turn off your caps lock. 2. The procedure is similar but slightly different for the VE30DE (92-94 SE-only).Turn key "on" but don't start the engine. Make sure the RED LED turns on when turning the ignition key the START position. I prefer to not shorten the codes by leaving out the zeros, because, as an example, in the following list codes 0111 & 1101 if shortened would both be code 111.

© Copyright 2017 postmapper.com. All rights reserved.