If the error immediately re-appears call HP for technical support. This configuration should eliminate or decrease the frequency of this error. All rights reserved. Recommended action Remove and re-install the Printhead cleaners.
If the printer continues to display the 79.00FE error, upgrade the firmware. Follow the additional steps below if the problem is not Parallel related or changes to configuration do not solve the issue. Can you hear the little "whoooooooop" of the mirror motor spooling up to speed? If the error re-appears, turn the printer off (using the main power switch). http://www.fixyourownprinter.com/posts/35332
If the operating system is any other operating system (such as UNIX or DOS), perform the next two steps, then proceed to section titled “Upgrade Process”. Articles Forum New Posts FAQ Calendar Community Groups Forum Actions Mark Forums Read Quick Links Today's Posts View Site Leaders Who's Online Blogs Advanced Search Forum Printer Forums Hewlett Packard Laserjets top System Error 010023 (non-continuable) Explanation EEROM test failure Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the Attempt to verify printer functionality.
Al Reply With Quote 02-02-2011,12:35 PM #4 redcow View Profile View Forum Posts View Blog Entries View Articles Senior Member Join Date Jan 2005 Location Elk Grove, California Posts 1,097 Interesting Click system Maintenance. You will need to check both before you can move on. 50.1 Fuser Error Hp 9040 Recommended action Turn the printer off (using the power switch at the back of the printer), wait 20 minutes and turn the printer on (condensation may be causing error and the
Reply With Quote 02-02-2011,07:13 PM #5 cs_steve View Profile View Forum Posts View Blog Entries View Articles Super Moderator Join Date Dec 2006 Posts 700 In weird instances, could be related Hp 5000 Fuser Turn the printer on, if printer initialization completes (printer goes to a Ready state), continue with Step 6. Re-cover the offending printhead(s). http://www.printertechs.com/printer-troubleshooting/369-50-1-error-on-hp-laserjet-5000-5100 Heck you could even order a maintenance kit from hp for a lot less money.
Click here for information on contacting HP Customer Care. 50.1 Fuser Error Hp 5100 If the error continues or persists, replace the Lens cover. This configuration should eliminate or decrease the frequency of this error. Open the cover on the back of the printer to access the ink cartridge assembly (right side of the printer, looking from the back).
top System Error 0C1000 (non-continuable) Explanation The primer is not calibrated or the calibration settings have been lost. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpp03771 Scroll to Clean Platen and press Enter. 50.1 Fuser Error Hp 4700 NOTE: Proceed with the following steps before pressing ENTER on the keyboard. 50.1 Fuser Error Hp 9050 The type of interface used on the printer (parallel or network).
I am getting a 52.0 error after each print. Sign Up Login Add Question sfe39 asked Jan 18, 2006 at 3:28pm 0 HP DesignJet 430 Error 50.2 HP Laserjet 5000n Hello all. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. Loosen the two thumbscrews that attach the HP Jetdirect EIO card. 50.1 Fuser Error Hp Laserjet P1102
Will they both work??? Click here for instructions on how to upgrade the printer's firmware . The files can be found in the default directory located in C:\Program Files\Hewlett-Packard\HP Designjet System Maintenance. An authorized HP Dealer or Retailer: Click here to go to HP's online Service and Support Locator .
If the error continues, call HP for technical support to troubleshoot the problem. Hp Laserjet 5100 Fuser J7 and J8 SDRAM are memory DIMM slots. If the 50.1 Fuser error message returns, it's time to replace your fuser.
by darrell fuller on Apr 25, 2007 at 8:37am Add comment Please sign in to comment 0 I don't know why it would work when you open and close the cover, Figure 3: Location of DIMM(s) NOTE: J6 - Boot ROM is internal printer firmware. top System Error groups The System Errors are organized in groups as follows: Group 01 - Hardware Test Group Group 03 - Laminator Errors and Warnings Group 04 - Intelligent I/O 50.1 Fuser Error Hp 6040 by roba on May 26, 2010 at 12:11pm Add comment Please sign in to comment 0 http://www.fixyourownprinter.com/specials/parts/fusers/S113 by moe on May 26, 2010 at 1:39pm Add comment Please sign in to
top System Error ffff ffff 01dcxxxx Explanation A problem with the I/O card has occurred (normally during power up). Unplug the power cable from the printer. Recommended action Turn the printer off, using the main power switch located on the back of the printer. Not really too tough to replace, with any technical skill.
Select the system software (firmware) according to what operating system is in use. Using the Arrow keys, scroll to Utilities and press Enter. top System Error ffff ffff 02b301b0 Explanation A firmware error occurred during a Printhead Alignment. top System Error 0A0060 (non-continuable) Explanation An ink leak in the Tubes System has been detected.
Recommended action Turn the printer off (using the power switch at the back of the printer). If any of the printers are out of date, the application will prompt an update.